null

Free domestic shipping for all orders over $150!

Carbon Coating Kit

Retail:
Was:
Now: $84.99 - $199.99
(You save )
(102 reviews) Write a Review

Description

Everything you need to get back hours of your life - and put them into woodworking where you want them! Prevent rust and reduce friction on your cast iron and other metal tools with a graphene coating that fills pores in metal. Add a nanolayer of protection that completely seals the work surface, providing long-lasting protection against water, oil, and chemicals, reducing wear and eliminating rust. Replace traditional waxes and sprays, and minimize maintenance, with Carbon Coat!

This kit contains the full Carbon Coating system, along with all the applicators you need to do the job. You'll find our "Carbon Cleanse" decontaminator for carbon coating application, which will allow you to fully clean your piece before Carbon Coating. Then apply "Carbon Coat" graphene protection for metal to seal your tool with a graphene coating that fills pores and completely seals the surface. Finally, apply "Carbon Glide" friction reducer for metal to further reduce friction - and get back the hours of your life you used to spend waxing, with a slick surface that installs quickly and doesn't melt.

Make protecting your tools easier with the Carbon Coating Kit: all the solutions and applicators you need - including our revolutionary new Coating Applicator Block system - in one convenient package. Welcome to the future of nanoprotection!

Additional Questions?

Check the Frequently Asked Questions page, and if you don't see your question there, contact us by calling 844-432-2266 or emailing cs@carbonmethod.com.

Carbon Coating Quick Kit For 1-2 Tools

  • 0.5 fl oz "Carbon Coat" graphene protection for metal
  • 2.0 fl oz "Carbon Cleanse" decontaminator for carbon coating application
  • 6.0 fl oz "Carbon Glide" friction reducer for metal
  • 1 Carbon Method Coating Applicator Block
  • 1 Capture Dowel
  • 10 Carbon Method Coating Cloths
  • 4 Carbon Coating microfiber buffing towels
  • 4 pairs of gloves
  • Instruction booklet

Carbon Coating Quick Kit For 2+ Tools

  • 1.0 fl oz "Carbon Coat" graphene protection for metal
  • 2.0 fl oz "Carbon Cleanse" decontaminator for carbon coating application
  • 6.0 fl oz "Carbon Glide" friction reducer for metal
  • 1 Carbon Method Coating Applicator Block
  • 1 Capture Dowel
  • 10 Carbon Method Coating Cloths
  • 4 Carbon Coating microfiber buffing towels
  • 4 pairs of gloves
  • Instruction booklet

Carbon Coating Quick Kit, Whole Shop

  • 2.0 fl oz "Carbon Coat" graphene protection for metal
  • 6.0 fl oz "Carbon Cleanse" decontaminator for carbon coating application
  • 6.0 fl oz "Carbon Glide" friction reducer for metal
  • 1 Carbon Method Coating Applicator Block
  • 1 Capture Dowel
  • 20 Carbon Method Coating Cloths
  • 8 Carbon Coating microfiber buffing towels
  • 8 pairs of gloves
  • Instruction booklet

Preparation for Carbon Coat is now easier than ever.

Simplify your Carbon Coat installation with Abrasive Pads and Reconditioning Oil from Carbon Method.

 

Our extra-thick 6" x 9" Abrasive Pads flex to work into pitted rust spots, and are faster and cleaner than sandpaper or steel wool. Abrasives are infused throughout the pad for long life, and they're designed to resist loading

 

Our Reconditioning Oil is the ideal solution for bringing your cast iron tool surfaces back to life. It lubricates and removes surface rust, staining, and pitted oxidation in cast iron surfaces, and is our recommended and ideal process to prep your tools for Carbon Coating.

102 Reviews

  • 5
    Carbon Coating Kit

    Published by John Soucheck on 24th Jul 2024

    My shop is located in my garages on a barrier island off the coast of Central Florida between the Atlantic Ocean and the Indian River. Read "Harsh Environment". I've recently treated my 2010 Saw Stop Industrial Table Saw. Rust is a constant battle. Over the years I've used paste wax, WD-40, Boeshield T-9, probably others with limited success. The most difficult and time consuming part of the Carbon Treatment is cleaning the surface. Started with mineral spirits to remove any remaining coating, then through 400, 800, and 2,000 non-woven pads lubricated with WD-40 , and driven by a cheap ROS. After this and prior to thorough cleaning, I worked a couple of small areas with pitting with medium and fine sandflex hand cleaning / polishing blocks. Then I cleaned the table top multiple times to remove all residue. I then applied the Carbon Coat Treatment. I won't go through this in detail since I followed the instructions in the supplied Application Guide exactly. My intent was to apply 3 / 4 coats as per the literature. However, since I did have a question and contacted Dan, the owner / founder, he suggested that they have had a lot of success in harsh environments with applying 6 coats, which I did. The application process goes quickly. However, since you need to treat small sections of the tool and you need to wait one hour between coats, you virtually dedicate a complete day to the process. Then, a day or two later, you apply a coat of Carbon Glide. The table has never been this 'slick', with wood almost 'floating' on the surface. I only completed this about two weeks ago, so at this point I don't know how well it will hold up and prevent further corrosion. I'll submit a follow up in about six months. One last comment, my interaction with Dan was excellent, he seems to be a great guy.

  • 5
    Fantastic product - Excellent Results

    Published by David - Tiller Trade Co on 18th Jul 2024

    We ran this coating on our saw stop for over a year and was blown away at the results! We used to get rust every 6 weeks or so when we used paste wax. After an entire year with carbon method, we have no real rust spot or pitting. Carbon glide is a great maintenance coating as well that helps keep the surface slick. Cant recommend this stuff enough!

  • 5
    Carbon coat

    Published by David Macintire on 17th Jul 2024

    Prep was very easy got everything cleaned and the carbon coat on. Waiting 48 hours to put on the carbon glide on and should be good to go. I did my new Harvey table saw and my Powermatic Band saw. I’ll follow up in a few week and post a review on my YouTube channel.

  • 5
    Carbon coat

    Published by Unknown on 15th Jul 2024

    Awesome, easy to apply, very happy to make the investment

  • 2
    Amazing to start, but quickly loses effectiveness

    Published by Kalamane on 8th Jul 2024

    This stuff feels amazing and provides a very low friction finish. The problem is that it didn't take very long for the coat to wear away, and I even had some rust appear where I had left parts clamping on the table saw surface for a few days. Would not recommend. Renaissance - Micro Crystalline is a superior product, will provide far more mileage for the cost (many times more as I use 1/100th, or 2ml, of a container for the table saw top whereas the Carbon Method requires 1/4 of the bottle)

  • 4
    Carbon Cleanser

    Published by Leon on 25th Jun 2024

    I bought the double pack for 2~4 machines. The rpoduct seems to be working so far. I will confess that I have not yet tested the new surface or the Carbon Glide. But 2~3 weeks after sealing the top, no rust!!! I recall BoeShield in a Texas Coast environment FAILED on the first day of aplication on a brand new table saw. I would suggest that the Carbon Cleanse size be enlarged a bit. Mine still has two surfaces to prep and I have about 1/3 of a bottle left. Yes I used as directed.

  • 5
    Carbon Metod

    Published by David Hard on 15th Apr 2024

    Excellent product. I have struggled with keeping my Iron in good shape. I have tried other products but this one tops them all. I applied it to my new Industrial Saw Stop and wow. What a difference. So I just ordered more to put it on My lathe, 20 planer, Jointer, Band saw and router table. Thanks Carbon Method.

  • 5
    Carbon Method

    Published by Robert Jacobs on 31st Mar 2024

    Beautiful results

  • 4
    Carbon Coating Quick Kit

    Published by Allen Ledet on 22nd Mar 2024

    Applied easily, took some time to prep tools. Applied coating to cabinet table saw, 15 inch planer, small table top jointer, bandsaw and oscillating sander. Had enough product for 3 coats on each. Glide coat made surfaces very slick.

  • 5
    Carbon Coating prep and quick kit

    Published by Ted Thompson on 15th Mar 2024

    This product was so awesome!. I live in very humid Texas and am constantly fighting woodworking equipment rust. The process was very clear and I am totally pleased with the results. I don't plan to ever use anything else in my shop and am already telling my fellow woodworkers about the products.

Related Products